Saturday, June 1, 2013

Phase II – The Island Structure



Phase II – the island structure (sounds like something from an aircraft carrier!)

We spent a few minutes with some short pieces of flooring to check out our layout. Using the actual wood was valuable since sketches and measurements can go awry, but a block of wood is pretty definitive!

We sat the Advantech subfloor up on the sawhorses and marked the cooktop cutout using a Sharpie marker.

Using the same techniques detailed in my earlier blog, I prepared the first course using the table saw to strip the tongue and the planer/jointer to produce a flat, smooth edge. The first course is always a solid piece if at all possible! 
Using the Ryobi power miter box, I cut the ends for a perfect fit.




After extensive checks and counter-checks, I was satisfied the piece was as properly aligned as my “finger feeler-gauges” could achieve and I clamped the piece using a 2X4 top board.


Once the first course glue set overnight, I was ready for the second course.


I made an access cut along the edge of the cook top cutout but left plenty of “meat” to allow a strong piece. The cutout simply allows clamps to be applied a little closer. 

Here’s the second course glued and laid up. I selected a 2X4 that has a slight bow as a top clamp press board. I placed the peak of the bow in the center and as I clamped the ends, the bow helps keep the piece tight against the subfloor. The tongue & groove will keep the close edge contained. To make sure the far edge is intimately bonded with the subfloor, I used the same “spring clamp” I used with the rollaround – a piece of 2X4 loosely clamped at close end and more firmly clamped at far end. The result is additional down force on the far edge.
A pipe clamp keeps the join seam tight (the second course is comprised of two boards). Edge clamping brings the second course in intimate contact with the first.


Liberal use of release sheets (plastic grocery bags) will help insure I do not accidentally glue a pressure block to the maple flooring!


A couple of 12” deep throat C-clamps help reach the work more easily. They won’t hold the same clamping force as the normal C-clamps, but they are sufficient.

Long shot of final layup for second course.

Next - Additional courses will be done similarly and I will not update as I go unless I change some method or other.

Finito! At least for the learning phase!





Finito! The learning phase is complete!

Here is the final product. There are a few “warts” that are not readily evident. But that’s why I did the rollaround top first! To learn.


My son David came over and carried the top up (I could have but it exceeds the limit my doc said to put on my new knees!) We installed it using L-brackets and cap screws. Looking pretty good!


Next – Phase II – the island structure (sounds like something from an aircraft carrier!)
 

Thursday, May 23, 2013

Final Assembly and Finishing



Ready for the End – of the Roll-Around Counter Top That Is!



I was unhappy with the way the end pieces lined up when I used the dowel pins, so I decided to go without any mechanical support, i.e. just the glue. I figure if it comes loose, I can always use the brad nailer when I reattach
The piece was just slightly too long for my pressure clamps, so I broke out the long pieces of pipe and shifted the pipe clamp hardware to them.  Vertical alignment was achieved using cheek blocks with a C-clamp. Again, I used plastic grocery bags as a release sheet between the blocks and the work. I did one end at a time - this is the final layup.


Once the work was completely set up, I used a block plane to even out the slight differences in the side and end band boards. (I found the plane in a flea market in Fla for $5 and my son Dave sharpened it to the point you can almost shave with it!)


Then I sanded bottom first (with the piece resting on an old throw rug) using 80 grit in the Black & Decker commercial grade orbital sander. I used multiple passes up and down while rocking the sander side-to-side  to “break” the sharp edge.
Sanded sides of band board, then turned the piece over and sanded the top. 
Changed sanding paper frequently - used 4 pieces of 80 grit and 2 pieces 120  grit.
Once it was all smooth, finish sanded with 120 grit.

Brushed dust off and then went over piece with a tack cloth.


Final piece ready for first coat of varnish – which I applied. After it sets up, I’ll sand again with 320 grit and apply the second coat of varnish. (I took a photo but it looks weird since some of the varnish has already started to dry leaving an uneven finish appearance.)

Next: Final coats of varnish and installation!

Monday, May 13, 2013

Monday May 13 - Fitting Band Boards



As it happens, the work is not perfectly flat! Don’t know if it is a thermal coefficient of expansion “fight” between the Maple and the Advantech or what.
Anyway, today, I completed the band board prep. Details below!

I decided on the stop board method with finger check, loosening the clamp if necessary to bring tops of band board into alignment with counter top. Then a tap with the rawhide mallet and a trip to the drill press.

End board being fitted . . .

. .  . and marked for miter saw cut . . .
. . . with the first cut just a smidgen long (“leave the line”).

Drilling side holes using dowling jig.
(Important tip: If you have screws in the countertop, don’t try to drill through them! It really does a number on the drill bit!)

Once again, using rawhide mallet so as to not mar the wood.

Once the side band board is cut, the process of fitting the miter corners begins. The key is patience – you can always cut more off but I haven’t found a supplier for 
“grow-some-board”
When you get really close, with the power miter box, you can swing the blade down (not running), bring the work right up to the side of the blade, hold it there while you make a cut. David and I call this “kissing the wood” – takes a very small amount of wood off.  This whole process may take 8-12 trips to the power miter box per corner, but its worth it when you get that perfect fit!

Ready to glue up side pieces! Now that all four corners have perfect fits, time to glue the side pieces. A cotton swab is perfect to wet the holes. The flat wood is again wet with the acid brush.

Here’s the piece with the two side pieces glued and clamped. The dark areas are just damp with water used to remove excess glue. 
Since the grain on the side pieces runs with the grain on the counter top, I can have it attached when I do my final passes with the belt sander.
I’ll clamp the belt sander into a woodworking vice to create a table belt sander and use that to dress the end pieces down to final fit.


Next: Gluing end pieces and final finish sanding with orbital sander.

Friday, May 10, 2013

Sanding and Edge Band Board Experiments



Friday May 10, 2013



I noticed that the boards had apparently NOT been through the sander at the mill inasmuch as the planer marks were pretty evident.  I worked it for a while with the Black & Decker commercial orbital sander and decided I needed a “bigger gun.”


I checked a Popular Mechanics review of belt sanders and they had good words for the Sears and the Chicago Electric (sold by Harbor Freight). As it happens, the Chicago Electric is on sale and is about half whet the Sears unit is, so I made the trek to Harbor Freight.

I fired the sander up and was making great headway but did not appreciate the removal rate, scratching, and differences in the effect on heartwood and sapwood!

I eventually brought the B&D orbital sander back after I had sanded the boards free from the planer marks. I have some learning to do with this belt sander!
 




Finally, I went to work on the “band board” which will surround the edge of the piece. I drilled one end of the countertop using a Sears dowelling jig I bought years ago.


I used some dowel marking inserts to establish the desired location for the mating holes in the band board. . . .


 . . .  and drilled them using the drill press with a depth stop set.



The aligment was not perfect (a tiny bit “tall” at one end), so I decided to try again on a fresh piece, this time using the dowelling jig and the drill press.

The results were way worse. I must cogitate on this. Maybe I need to dowel it a smidgen “tall” and gradually work it down with a plane? Need to consult #1 son.
Stay tuned!


Wednesday, May 8, 2013

When we built our house in 1986, we finished the interior ourselves. We chose some very nice cherry kitchen cabinets (Continental Kitchens in Shelbyville) and they have held up very nicely.
Due to financial constraints, we installed laminate countertops which looked nice but are past their prime, to say the least. The substrate is de-laminating over the dishwasher and there are numerous chips and peels. Time for new countertops. Have you shopped for countertops lately? All of the hard surfaces have some flaw- they either absorb oils, scratch, or discolor is a hot pan is placed on them.
While watching a TV cooking show one day, I noticed that their countertops were wood! So I did a little surfing and came up with several ideas. The one I liked best was using maple hardwood flooring. Maple trees are indginous to Indiana, produce very hard wood (think basketball floor!) and are a lovely pale off-white color, very similar to the laminate lights color (did not want dark counters withe the dark cabinets.
Did some research and found a mill in Spencer Indiana - 40 mile drive - that will sell unfinished flooring! 
A few weeks ago, David, our son, and I drove down and picked up 60 square feet of 3" unfinished maple flooring milled with tongues & grooves.
I have been planning and buying materials ever since and am now ready to commence.
On the advice of Scott Nesbitt, a good friend and jack of all trades, I am using AdvanTech subfloor as the substrate (the flooring tongue & groove system assumes a strong substrate to support the floor).
Found the AdvanTech at Carter-Lee in Indy and went there with good friend (and pickup truck owner) Terry Pavlack and bought three sheets (one for the island and two for the main L-shaped countertop. Last week, David came down and we trimmed the island piece to size with a hand held power saw (using a 2X4 clamped as a saw guide).
One of the scraps is big enough to act as a substrate for a small utility cart, and I decided to start small and learn before I jumped into teh deep end.
This morning, I cut the AdvanTech to size and selected pieces of flooring. The next episode will chronicle the assembly of that piece.